Vladyslav Pereverzyev

exocad Smile Creator: smile design from photo to mock-up

exocad Smile Creator step by step: align photos and face scans, set the lip line and guidelines, model teeth in 2D and 3D, then export the report and mock-up.

Smile Creator is the exocad DentalCAD module for smile design. It brings patient photos or a face scan into the design, so the anterior teeth are modeled against the face and the lips instead of only on the jaw scan. This post follows the Smile Creator workflow as documented in the exocad wiki for current releases, with notes on the steps where cases usually go wrong. For the broader lab process around smile design, see digital smile design in the dental lab.

Requirements

The Smile Creator module has to be activated. The wizard shows the Start Smile Creator step when at least two neighboring teeth are reconstructed and at least one of them is an incisor. It can also be opened from the main toolbar under Tools. The module is optimized for a single group of neighboring teeth and it is not available when the reconstruction type is a wax-up with a wax-up scan.

Loading the retracted photo

The first image is a retracted view of the teeth. Load it from a file, take it with a connected camera, drag and drop it into the main view, or paste it from the clipboard. exocad publishes a Smile Creator photo protocol and following it makes the automatic steps much more reliable.

To use the automatic facial feature detection, you accept the supplemental terms for exocad’s online features. The software then segments both jaws and aligns the photo with the jaw scan automatically. Check the overlay and continue if it is correct. Without the online features, or when the automatic result is wrong, the alignment is done manually.

Aligning photos and scans manually

Manual alignment uses two corresponding points: click two points on the scan, then the same two positions on the photo. The points can be dragged afterwards and scrolling over the images magnifies them. In the next screen the scan and the photo are shown on top of each other. Drag the photo with the left mouse button, change the view angle of the scan with the right button and switch the scan display to an outline if that makes the edges easier to match.

The smiling photo is loaded the same way and aligned to the retracted one, automatically or with two points. A Field of View slider compensates for differences in camera and lens. Take the time to get both anterior and posterior teeth aligned, because every later step depends on it.

Using a face scan

Instead of 2D photos you can load a 3D face scan. Set two corresponding registration points on the face scan and on the jaw scan, then refine the alignment by moving and rotating the jaw scan, using the left, front and right views. Capture tips for face scans are in iPhone face scan for smile design.

Lip line and guidelines

The software detects the inner lip line automatically. If detection fails, click points along the inner lip line to cut out the mouth, then adjust them by dragging.

The eyes are also detected automatically, or you click the patient’s right eye and then the left eye. Guidelines and curves appear from these references. A drop-down in the wizard selects a proportion guide and Add lines and curves adds further guidelines, which can be moved by their control points. Lock Rotation with align image to lines straightens the image to the references.

Modeling the teeth

The modeling screen shows the photo with the 2D tooth outlines, plus front, top and side views of the 3D model. Choose the tooth library first. Changing the library later resets every modification you have made.

Mirror Movements applies position, size and rotation changes symmetrically. Click a tooth to change its size, shape or position in any view, hold Ctrl to select several teeth, or hold Shift to select all teeth between two clicks. Free-Form edits the tooth shape directly and Measurements shows tooth dimensions and proportions. The visual modes show the full tooth, a preview above the cervical border (useful for gummy smiles), or an outline.

Preview, color and gingiva

The preview step compares the previous and the new smile with a before and after slider. Tooth color can be chosen from 20 standard colors, adjusted with a 2D color bar, or picked from the photo with a base color and a highlight color. The colors in the photo depend on camera, lighting and display, so the preview is an approximation of the final shade.

A gingiva can be generated and then shaped with free-form tools and light and shading controls make the result look more natural. A photorealistic preview of one or both jaws takes a few minutes to generate. The image with the new smile, alone or next to the previous one, can be copied to the clipboard or saved in the project folder.

Report and next steps

The last step creates a PDF report with page size, orientation and theme settings and you choose what it includes. Screenshots with captions added during the workflow can be included. The report can be exported or printed and a TruSmile video can be created from the same screen.

After Smile Creator, a Smile window stays available from the main toolbar while the design continues in DentalCAD, so tooth placement can be checked against the face. The next wizard step is the mock-up, which transfers the design to the mouth for the patient to try.

When the approved smile is to be placed with composite instead of ceramic, the same design becomes the model for the composite injection technique.

Source: exocad wiki, Smile Creator.

Frequently asked questions

When is Smile Creator available in exocad?

The module has to be activated in the license. The wizard shows the Start Smile Creator step when at least two neighboring teeth are reconstructed and at least one of them is an incisor. It is not available for a wax-up with a wax-up scan.

Can Smile Creator work with a face scan instead of photos?

Yes. You set two corresponding registration points on the face scan and on the jaw scan, then refine the alignment manually.

Does Smile Creator use AI?

Current releases use AI to detect facial features, the lip line and the eyes and to align the photos with the scans. The automatic detection uses online features that require accepting exocad's supplemental terms. Without them, the alignment is done manually.

What comes after Smile Creator?

The design continues in DentalCAD, where a Smile window keeps showing the result relative to the face. The next wizard step is the mock-up.