Vladyslav Pereverzyev

Two-layer injection: dentin and enamel models from one wax-up

The two-layer injection technique in exocad: one wax-up, a reduced model for the dentin index, a full model for the enamel index and how to keep them aligned.

The single-shade injection technique gives the planned shape, but the color can look flat on large anterior cases. The two-layer version uses two indexes from the same design: the first injects a dentin shade into a reduced shape, the second injects an enamel shade over it into the full shape. This post explains, for labs designing these cases in exocad, how to get both models from one wax-up and keep them aligned.

The principle

Both models come from the same design. The full wax-up gives the anatomic model, with the final shape of the teeth. A reduced version of that wax-up gives the second model, where the labial surface and the incisal edge are set back by the thickness planned for the enamel layer.

Step at the chair Index made on Injected shade What the layer gives
1 The cutback model Dentin Core, opacity and body color
2 The full anatomic model Enamel Final shape, translucency at the edge

The order at the chair is the reverse of the order in the design. The lab designs the full shape first and reduces it afterwards. The dentist injects the reduced shape first and covers it with the full one.

Designing the full wax-up

The first step is the normal wax-up for the composite injection technique: additive, smooth at the gingival margin, checked in occlusion and approved by the clinician. Everything that follows depends on this shape, so changes are made here and never on the reduced version alone.

Creating the reduced anatomy

exocad DentalCAD creates reduced parts from the full anatomic shape with its shrinking and cutback tools and the Anatomic Reduction step lets you define the regions where the material is taken away. These tools were made for frameworks that receive veneering ceramic and they work just as well for the dentin core of an injection case. A few points matter more here than for a ceramic framework.

  • Agree the thickness of the enamel layer with the clinician before reducing. It depends on the composite system and on the shade effect they want.
  • Reduce evenly on the labial surface and at the incisal edge, where the enamel shade gives translucency. The cervical third usually needs little or no reduction, since the composite there is thin anyway.
  • Keep the reduced shape smooth. Sharp steps or mamelon shapes look good on screen but trap air when the composite flows in.
  • Leave the palatal surface as it is, unless the clinician asks otherwise, so the first index has a stable support.

Saving two models from one case

Each shape becomes a closed model with the scanned arch, in Model Creator with Digital waxup model as the model type: once with the full anatomy, once with the reduced parts. Each is saved as its own file. Clear names prevent the most common mistake, which is making the first index on the wrong model. A naming pattern like case number, arch and “reduced” or “anatomic” is enough.

The two models must share the same position and the same base. If the base or the position changes between them, the second index can still fit on the teeth, but any comparison or check against the first model becomes harder.

Printing and checking

Both models should be printed on the same printer, with the same resin, the same orientation and the same post-curing. Different settings can change dimensions slightly and the second index sits on the first composite layer, so small differences matter. The posts on resin calibration and post-curing cover the printing side.

Before sending, put the two models next to each other and check that the reduction is visible where it was planned and absent where it was not. A reduced model that looks almost identical to the anatomic one usually means the cutback was not saved.

When two layers are worth it

Two layers add a model, an index and chair time. They make sense on large anterior cases where color depth matters, on teeth with strong discoloration and on cases where the patient expects a result close to ceramic. For small corrections or posterior wear, a single shade is usually enough.

Labs that offer the technique without having the design time can send both versions as one job for CAD design and receive the anatomic and the reduced model ready to print.

Frequently asked questions

Why use two models instead of one?

A single model gives one index and one composite shade. With a reduced model the dentist first injects a dentin shade into the smaller shape, then uses the full model's index to inject the enamel shade over it, which gives depth to the color.

How much should the anatomy be reduced?

There is no single value. The thickness of the enamel layer depends on the composite system, the shade and the clinician's plan, so the lab agrees it with the clinician before the design and reduces evenly where the enamel layer should be.

Do the two models need to be printed together?

It is safer. Printing both on the same printer, with the same resin and settings, keeps their dimensions consistent, so the second index sits correctly over the first composite layer.

Which tool creates the reduced anatomy in exocad?

DentalCAD reduces a full anatomic shape with its shrinking and cutback tools, the same ones used to make room for veneering material. The reduced parts are then turned into their own digital waxup model in Model Creator.