CAD design
Design technique for crowns, bars, abutments and full-arch work: how production-ready dental CAD files are actually built.
-
CAD design
Composite injection technique: designing the models in exocad
How the lab designs the wax-up and the printable models for the composite injection technique in exocad, from the scan to a model the clinic can use.
-
CAD design
Digital facebow in exocad: aligning the scans to the articulator
How a digital facebow reaches exocad: scanner transfer, digital facebow data, manual and three-point alignment, photo alignment and the checks before design.
-
CAD design
Angled screw channels in exocad: abutments and bridges
How angled screw channels work in exocad: when the library allows them, how to set the angle, the screws and Ti-bases they need and the design limits.
-
CAD design
RotoClick model system: facebow and printed models in exocad
What the RotoClick model system does in exocad: the library, the facebow digitized with an intraoral scanner, printed models in the articulator and calibration.
-
CAD design
Snap-on smile: designing removable veneers in the dental lab
How the lab designs a snap-on smile, a removable veneer shell over the natural teeth: scans, design, material, retention and when clinicians use it.
-
CAD design
Two-layer injection: dentin and enamel models from one wax-up
The two-layer injection technique in exocad: one wax-up, a reduced model for the dentin index, a full model for the enamel index and how to keep them aligned.
-
CAD design
Blender for Dental surgical guides with the Guide Designer
How Blender for Dental surgical guides are designed with the Guide Designer: 3D Slicer link, CBCT alignment, implant planning, sleeves and guide frames.
-
CAD design
Dental CAD design in South Tyrol: outsourced design for labs
Dental CAD design in South Tyrol for labs: how outsourced design from Bolzano works, what to send, files returned and support in Italian, German and English.
-
CAD design
exocad PartialCAD: designing a removable partial framework
How exocad PartialCAD designs removable partial denture frameworks: survey, relief, clasps, connectors, finish lines, retention and the hardware it needs.
-
CAD design
Eggshell temporaries in exocad with the Provisional Module
How to design eggshell temporaries in exocad with the Provisional Module: pre-op scans, eggshell crowns and pontics, anatomic pontics, thickness and printing.
-
CAD design
Screw-retained crown on a Ti-base in exocad, step by step
How to design a screw-retained crown on a Ti-base in exocad: DentalDB setup, scan body matching, screw channel, emergence profile, thickness checks and export.
-
CAD design
Multilayer zirconia: positioning the restoration in the disc
How to position restorations in a multilayer zirconia disc: shade and strength gradients, vertical position, nesting, connectors in bridges and sintering.
-
CAD design
exocad Bar Module: designing implant bars step by step
How implant bars are designed in the exocad Bar Module: pillars and segments, bar profiles, planes and insertion axis, attachments and superstructures.
-
CAD design
exocad cement gap settings: crown bottom parameters explained
What each exocad cement gap and crown bottom parameter does: gap zones, axial and radial spacing, crown border, undercut block-out and milling compensation.
-
CAD design
exocad Smile Creator: smile design from photo to mock-up
exocad Smile Creator step by step: align photos and face scans, set the lip line and guidelines, model teeth in 2D and 3D, then export the report and mock-up.
-
CAD design
Zirconia minimum thickness and connector size for CAD design
Zirconia minimum thickness and connector size from manufacturer instructions: why translucent zirconia needs more, example values and how to check in exocad.
-
CAD design
exocad Bite Splint module: occlusal splint design step by step
How to design an occlusal splint in the exocad Bite Splint module: scans and bite, border and thickness, contacts and guidance, then printing or milling it.
-
CAD design
exocad Full Denture module: the digital denture workflow
How digital dentures are designed in the exocad Full Denture module: model analysis, tooth setup, denture base and milled, printed or monolithic output.
-
CAD design
3D printed dental models with exocad Model Creator
How exocad Model Creator turns scans into 3D printed dental models: plate or plateless bases, removable dies, implant analogs, gingiva masks, printing.
-
CAD design
Surgical guides in exoplan: how Guide Creator works
How surgical guides are designed in exoplan with Guide Creator: implant planning, sleeve or sleeveless protocols, drill kits, anchor pins and libraries.
-
CAD design
Monolithic zirconia crowns in exocad: a design workflow
An exocad design workflow for monolithic zirconia crowns: margin and insertion axis, cement gap, tool compensation, minimum thickness and CAM handover.
-
CAD design
exocad virtual articulator and jaw motion: a practical guide
How the exocad virtual articulator and Jaw Motion Import module work, when dynamic occlusion matters and how to transfer a physical articulator setup.
-
CAD design
iBar system in Blender for Dental: Toronto bridge design
How the B4D iBar system designs a Toronto bridge in Blender for Dental: bar and superstructure as separate parts, design sequence, materials, common errors.
-
CAD design
Implant abutment types: Ti-base, custom or multi-unit
Implant abutment types from a CAD designer's view: stock, Ti-base, custom milled and multi-unit abutments, when each fits and what to check before design.
-
CAD design
Digital smile design in the dental lab: photos to mock-up
How a dental lab runs digital smile design: the photos and scans it needs, natural tooth proportions, the 3D wax-up, the mock-up and gingival changes.